A Technical Introduction to Audio Cables

What is so important about cables anyway?

One of the most common questions asked by consumers faced with purchasing cables for their audio or home theater system is, "What is so important about cables anyway?" They can cost as much or more than some of the hardware in the system and to many it is difficult to understand why wire isn't just wire.

To begin to understand how audio cables work, we have to start with the two fundamentally different types of audio cables you are likely to have in your system. The first type of cable is called an interconnect, which is used to connect various components together (such as a CD player to a receiver). The second type of cable is called the loudspeaker cable (this is the wire going from the receiver or amplifier to the speakers). It is important to realize that both types of cables are carrying the same information, just with different amounts of energy.

Interconnects carry a signal with very little energy. These cables only need just enough energy to convey the information from the source, for example a CD player, to the amplifier. The low energy requirement means that the signal in interconnects has very little current (usually in the range of thousandths of an amp).

Loudspeaker cables on the other hand, carry a large amount of energy. All of the energy required to move the speaker cones and make sound must come through the loudspeaker cables. Because of the high-energy requirement in these cables the current is relatively high (currents can reach 10 amps or more).

The very basic reason why audio cables are important is because they change the signal going through them. There are two different, fundamental ways that an audio cable can change the signal. The cable itself can change the signal, or the cable can allow outside sources of energy to change the signal.

In order to understand how these two situations can occur, some basic background electrical knowledge is needed.

Signals in all types of wires are conveyed by the combination of voltage and current. Every signal has some amount of voltage and some amount of current. The larger the difference in voltage between two places, say the beginning and the end of a cable, the larger the amount of current, and vice-versa. The direct analogy to voltage and current is the flow of water through a hose. The amount of water flowing through the hose is analogous to current. The water pressure in the hose is analogous to voltage. The higher the amount of water pressure, the more water will flow through the hose. The higher the amount of voltage, the more current will flow through the wire.

Every cable has a set of electrical properties that can be measured using standard electrical testing equipment. The three most basic properties are resistance, capacitance and inductance. While a detailed description of these three different electrical properties is outside the scope of this article, a basic description of the relevant effects of these three properties can be given.

- Resistance opposes current. The higher the resistance the greater the amount of energy that is removed from the current and turned into heat.

- Capacitance opposes changes in voltage. If a voltage is increasing, capacitance will cause the voltage to increase more slowly. If a voltage is decreasing, capacitance will cause the voltage to decrease more slowly.

- Inductance opposes changes in current. If current is increasing, inductance will cause the current to increase more slowly. If current is decreasing, inductance will cause the current to decrease more slowly.

The final piece of background knowledge that is needed for this article is what the audio signal looks like. If one were to take the speaker cover off a speaker to look at the speaker cone while music is playing, you would see that it is moving back and forth. In order to move the speaker cone back and forth, the electrical signal must push and then pull the cone in rapid and repeating fashion. This is accomplished by having an Alternating Current, or AC.

Alternating Current simply means that the voltage oscillates between positive and negative. Because the voltage drives the current, this means that the current also goes positive and negative. In other words, the current is going back and forth in the wire, just like the speaker cone. The subtle variations in how fast the voltage and current go back and forth creates the different sounds that we hear when listening to music.

How a cable itself affects the audio signal

Now, going back to the ways that the cable itself can change the signal going through it, let's consider both types of cables separately.

As stated previously, interconnect cables carry a very small amount of current. Relative to the current the voltage is large. Because of that fact, capacitance is important, but inductance is relatively unimportant. As the voltage oscillates between being positive and negative, the capacitance slows the voltage changes down, and causes delays. This can cause audible distortion in the sound. Because interconnects have very little current, resistance is not much of a factor. Even an interconnect with extremely high resistance will only remove an infinitesimally small amount of energy.

The signal in loudspeaker cables is essentially the opposite of the signal in interconnects. Both cables have the same information, but in loudspeaker cables, the voltage is small and the current is large, relatively speaking. Because of the high current, both resistance and inductance are important in loudspeaker cables. The higher the resistance, the greater the amount of energy that will be absorbed by the cables. The resistance will not cause any distortion, but it will decrease the volume of the sound. The inductance on the other hand, can cause distortion. As the current oscillates between being positive and negative, the inductance slows the current changes down, and causes delays.

How a cable lets outside sources of energy affect the signal

As stated previously, the second fundamental way of altering a signal passing through an audio cable is to introduce outside sources of energy. This outside energy is typically termed "noise". By definition, if any energy is absorbed by the signal, the signal has been distorted.

There are many potential sources of noise around audio cables. Some of the more common sources of noise, such as radio frequency waves, are familiar to most people. When wiring up a radio, frequently a consumer must attach an antenna. Antennae are intentionally designed to channel radio frequency energy into a stereo. Just like an antenna, it is entirely possible for an audio cable to pick up radio frequency energy. If you are not intending to listen to the radio, this is not a welcome effect.

Electronic components, electrical cords, sound waves, and even the sun, are all capable of creating noise. Electrical cords create electromagnetic fields around them that can transfer energy to a cable. Sound waves create mechanical vibrations that can be transformed into electrical energy that is added to an audio signal. Because there are so many different types of noise, there are many methods used to prevent a cable from picking up noise. Shielding, twisting of conductors, and mechanical damping are all common noise protection methods in cables.

While noise affects both interconnects and loudspeaker cables, generally the effects are far more significant in interconnects. This is because the signals in the interconnects have far less energy. Since most forms of noise are inherently low energy to begin with, this means that it is far easier for them to modify the low energy interconnect signals than the high-energy loudspeaker cable signals.

Macro vs. Micro

The parameters discussed so far have been primarily "macro" effects. These are for the most part the top-level parameters that effect cables. These parameters as well as others not discussed here also exist at a "micro" level. Taking capacitance as an example, a given cable will have an overall capacitance that can be measured. This overall capacitance is a "macro" level parameter. The same cable can also be analyzed as 1000 separate but connected pieces. Each piece will have a local capacitance. These local parameters are "micro" effects and can have their own impact on the signal separate from the "macro" effects.

The impact that the "micro" level parameters have on an audio signal is usually less than the impact of the "macro" level parameters. However, they do still make a difference in the signal transfer. The various ways that audio companies choose to either mitigate or ignore these "micro" level details is, in part, responsible for the vast array of different cable designs. From cryogenic treatments and precious metal wires, to fine silk insulation and fluid filled cable jackets; extreme cable designs abound.

Will I hear the difference?

The fact of the matter is that cables do alter the sound going through them, and that it is audible. You do not need to be an expert, or an audiophile, to hear the difference. To demonstrate this point, simply listen to your stereo. If you close your eyes, does it sound like the music is being played live right in front of you? This is what audiophiles strive for, and unless you have a very high-fidelity system, your answer to this question will most likely be no. You may have a hard time describing what exactly does not sound right about your system, but you know that it doesn't sound like a live performance.

Of course, the reason why the music does not sound live cannot be blamed solely on the cables. The degradation of the sound occurs in every component of your system. However, the point here is that even a casual listener can detect the subtle distortions that can prevent music playback from sounding live. Improving the quality of your audio cables will improve the sound quality of your system.

It is fairly safe to say that no matter what cable you use, the modifications to the sound will be small. Audio cables will never cause a listener to hear a piano when a flute is being played. However, it is the small detail that makes all the difference between good and bad quality sound. That is why very strong opinions are formed about various cables.

As audio systems continue to improve in accuracy, listening to a "live" performance in your living room gets closer to reality. Cables are an enabling factor for advancements in audio reproduction and can play a remarkably important role in your system.

Adam Blake CEO / Co-Founder Pear Cable, Inc.
http://www.pearcable.com
For a more detailed explanation of cable design theory that Pear Cable thinks is relevant, see the "cable design" white paper available on pearcable.com

---

Obsolete Is A Dirty Word (Intel Pentium 64 Bit Microchip)

Get ready everyone, home computers are about to set new... Read More

What is EEPROM ?

EEPROM stands for Electrical Erasable Programmable Read Only Memory and... Read More

Ten Tips to Safeguard Your Laptops

The following is a list of tips to help safeguard... Read More

A Short Introduction to Blu Ray

Blu ray is a next generation optical media format developed... Read More

Batteries for Your Laptop

With technology advancing more every day, electronics have become smaller... Read More

Routing, Routed, and Non-Routable Protocols

ROUTING PROTOCOLSA generic term that refers to a formula, or... Read More

Top Three Factors to Consider While Choosing a Data Center for Your Business

Data Centers are the core of the Internet. The computer... Read More

Emergency Response VSAT Internet Communications

As 2005 begins, there are a number of products on... Read More

Would You Like An Extended Warranty With That?

Should you buy an extended warranty with your laptop? You... Read More

Tips To Select Proper Motherboard

Selecting motherboard is really simple. As name suggests "Motherboard" acts... Read More

How to Purchase a Flat Panel TV

When purchasing a flat panel TV, there are a few... Read More

Computer Network Installation

Computer network installation has become an essential prerequisite for any... Read More

Expansion Cards Part 1: (of a 3 part series)

PCIThe expansion slots available on motherboards allow for a variety... Read More

How to Check Your IP

So you need to check your IP address, for whatever... Read More

Be Free with Wireless Speakers

Are you tired of laying wires through your house, creeping... Read More

Buying a New Computer

Someone recently asked me "I teach senior citizens in a... Read More

Building A PC

Many people simply go to the retail store and get... Read More

Unclogging Epson Print Heads

Tools needed:1 - 10cc Injector1 - 4" - 5" of... Read More

Getting The Proper Laptop Screen Size

Are you sick of viewing everything on that small screen... Read More

Pixel Disruption To Cause Nausea From User of Computer Screen

As we study the issues associated with teaching kids in... Read More

ATA vs SATA

Hard Drives: ATA versus SATAThe performance of computer systems has... Read More

How to Choose The Right Laptop Accessories?

The notebook computer is coming of age. For the first... Read More

DVD Recorders: Getting Started

IMO, these sd work 'like a VCR' as far as... Read More

Coping with a Serious Data Loss from your Computer Hard Drive

Data loss is an expensive reality. It's a hard fact... Read More

A Review of Samsung Laser Toners

Samsung laser toner is just as popular as its Hewlett-Packard... Read More

Used Laptop Computer: Your Quick Purchase Inspection Guide ? Part 3

Used laptop computers are everywhere these days. How can you... Read More

Using System Restore to Save Yourself from Formatting Your Hard Drive

It is the most annoying thing when one day you... Read More

Can I Use My Old Ink With My New Printer?

The quick answer is...yes and no.Consider this. How many printer... Read More

What Is A Fuse? And How To Test It.

A fuse is a very thin wire, which either melts... Read More

A Look at Laser Toners

Laser toner is the ink for laser printers. It is... Read More

Correctional Institution Preventive Maintenance Software

There is a great need for preventive maintenance in correctional... Read More

Purchasing Laser Toner Refills

Laser toner refills can be expensive. Over the life of... Read More

You Can Prevent Computer Slowdowns & Issues

Most people understand preventive maintenance like changing the oil in... Read More